2/4/2024 0 Comments Cateye cycle computer![]() For accuracy, set by the radio time signal. *When you press the SET button, the undisplayed seconds will turn to zero. Press SET button to complete time setting. Then press M button, and hours will flash. Set the time one or two minutes ahead of the current time. To advance rapidly, hold down the button. Press S/S button to advance minutes by one. Then press SET button, and minutes flash. Press M button over 2 seconds to select, and stop it with S/S button. Revise the number as desired according to the instructions in (3). The stored number will flicker on the sub-display. Set main unit in ODO with M button, and stop it with S/S button. ![]() Resetting or changing the wheel circumference ODO will be displayed, and the desired number is set. When the desired number appears, press M button. To increase rapidly, hold down the button. For revision, press S/S button to increase the number by one. When using 216 cm without revision, press M button. The standard wheel circumference of 216 cm for 27" wheel is displayed. Press M button to set desired speed scale. Km/h and mile/h are alternately displayed with each press of S/S button. Then mile/h alone will be displayed as illustrated in fig.5. Or, the "Selecting Values Cross Reference Table" tells you an approximate circumference according to tire size. Mark the start and the end of the revolution on the ground and then measure the distance between the two marks. Put a mark on the tire tread and ride the bike one full wheel revolution. How to measure wheel circumference (L) of your bike The following must be completed before operating. Since all memories are erased, set necessary data again according to "Main Unit Preparation". This should only be executed after replacing battery or when irregular display occurs due to static electricity, etc. All displays illuminate, then mile/h symbol illuminates. When M button, S/S and set buttons are pressed simultaneously, all data stored (ODO, speed scale, Wheel circumference and clock time) is erased. (When done in ODO, registered wheel circumference will be displayed.) Select any mode except ODO, then press M button and S/S button simultaneously. In TM, DST or AVS mode - On/off the Auto function.When pressed in stop state in each mode, the following can be revised. This is for setting the wheel circumference and clock time, switching on/ off Auto Function and to clear all present data and any irregularity. In Auto Function, this button is invalid. During operation, speed scale symbol flashes. Starts and stops the measurement of trip distance and elapsed time. *If held over 2 seconds, 12-hour clock appears. Cycling computers are weather resistant too, allowing you to keep cycling no matter what the elements may throw at you.Cateye Mity 2 CC-MT200 - Cyclocomputer ManualĬhanges the display in the order shown below, and data is displayed on the sub-display. Made to lastĬatEye cycling computers are designed to be strong and durable, yet also lightweight enough so that they won't impact on your cycling performance. ![]() All of this information can easily and quickly be transferred from the cycling computer to a mobile phone or PC.ĬatEye cycling computers with GPS are easy to install on any bicycle. This can be highly useful for planning routes, reviewing your training, or simply to see just how far you have cycled during a particular ride. Some CatEye cycling computers also offer a GPS function, which allows you to review your rides on a cycle map. In wired cycling computers there is a small wire running along the bike from the sensor to the computer, but a wireless system transmits the data wirelessly. The computer is attached to your bike handlebars and displays information taken from a sensor, which is attached to your bicycle wheel and bicycle frame. Different models availableĬatEye offer both wired and wireless models of cycling computer. For more serious cyclists a high end CatEye computer can become a useful training aid, tracking your progression and encouraging you to improve. Get your stats whilst you cycleĬatEye cycling computers are designed to provide you with real time information whilst you cycle, such as your speed, distance travelled and how many calories you've burned off. Whether you are a serious pro rider looking for data on your riding performance or an amateur cyclist looking to track your routes, there are many options available. Available in a number of different designs and functionalities, CatEye cycling computers and GPS have a range of useful features built in.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |